91TV

The walkaround is the simplest safety tool we have. It needs no special equipment, only time and attention. Ten minutes at the start of the shift is a small price to make sure the machine, and everyone around it, gets through the day in one piece.
By Clay Layne

Every operator has heard it a hundred times: walk around your machine before you start it. When you hear it so often, it can make it easy to stop taking it seriously. The walkaround slowly turns into a quick glance on the way to the cab, followed by a checklist marked the same way it was marked yesterday. This is what we call “pencil whipping the walk around”.

That is a mistake. At a landfill or transfer station, the loaders, compactors, dozers, excavators, and articulated trucks work in some of the harshest conditions in any industry. A proper walkaround can be done in 10 to 15 minutes regardless of the type of machine. It is the last chance to catch a failing brake line, a hydraulic hose rubbing on the machine, a loose lug nut, a cracked weld, a smoldering pile of debris before it turns into a fire, a broken or cracked step, a breakdown on the working face, or an injured coworker.

The walkaround is not paperwork—it is a safety device, and it only works if we use it the right way. The walkaround inspection form needs to be filled out daily and immediately turned in per company policy.

Why Our Sites Are Hard on Machines
91TV equipment does not fail the same way construction equipment does. The material we handle attacks machines in ways that build up quietly over a shift. Wire, strapping, cable, carpet, and plastic film wrap around axles, drivelines, and track rollers. Paper, fines, and dust pack into engine compartments and belly pans, where they sit next to hot exhaust parts. That combination is one of the most common causes of equipment fires at solid waste facilities. Rebar and scrap metal can be forced through guarding or doors into the engine compartment. Wood and other debris can become projectiles and break windows on equipment. Dust clogs radiators and air filters until engines overheat.

The landfill adds steep slopes, soft ground, mud, and leachate that eats away at metal. The transfer station adds tight quarters, push walls, constant backing, and pedestrians on the tipping floor. Many sites also share machines between shifts, which means the operator starting the shift may not know what happened to the machine the night before.

What a Proper Walkaround Covers
A good walkaround follows the same pattern every time to ensure that nothing gets skipped. Start with the machine parked on level ground, the attachments lowered, and the parking brake set:
• The Approach: Look at the ground under and around the machine for fresh fluid spots, debris, and anyone working nearby.
• Wrap and Buildup: Check axles, drivelines, tracks, and rollers for wrapped material. Open the engine compartment and belly pans and look for packed debris near exhaust parts and turbochargers. Clean it out before you start.
• Fluids and Leaks: Check engine oil, coolant, hydraulic fluid, and fuel. Look for wet hoses, weeping fittings, and damaged hydraulic cylinders.
• Tires, Tracks, and Wheels: Look for cuts, punctures, low pressure, missing compactor cleats, and loose track pads.
• Structure and Attachments: Inspect pins, bushings, cutting edges, the bucket or blade, and the ROPS/FOPS for cracks or damage.
• Access: Make sure steps and handrails are solid and clean so you can keep three points of contact getting on and off.
• Visibility and Warnings: Clean the windows, mirrors, and cameras. Confirm the lights, horn, and backup alarm work.
• Fire Protection: Check that the extinguisher is charged and the fire suppression system, if the machine has one, shows ready.
• After Startup: Buckle the seat belt, watch the gauges and warning lights, and test the brakes and steering before you move.

The Shortcuts That Hurt People
Most walkaround failures are not because people do not know how to do one. They happen because of habits:
• “It was fine yesterday.”
• “The night shift would have said something.”
• “I’ll catch it when I grease it.”

The checklist gets filled out in the break room, or only the side of the machine facing the parking lot gets checked. Small problems get ignored too. A slow leak, a backup alarm that sounds weak, or a step that wobbles a little all seem minor at the start of a shift. At the end of a 10-hour day on the working face, they are not.

The fix is to make the inspection physical. Operators should touch the items they check, open the doors they are supposed to look behind, and write down what they actually found. A checklist with the same marks every day for a month is a warning sign, not proof of a good machine. Give every operator clear authority to tag out a machine they believe is unsafe, without arguing about it.

Supervisors Set the Standard
Operators take the walkaround as seriously as their supervisors do. If the schedule expects machines moving the minute the gate opens, inspections get rushed. Build the time into the start of every shift and protect it.

Supervisors should walk around a machine with an operator now and then. It shows the inspection matters, and it is a good chance to coach newer operators on what to look for. Most importantly, act on what gets reported. If an operator writes up a leaking hose and it is still leaking a week later, they will stop writing things up. Close the loop: record the defect, the date, and the repair, and tell the operator it was fixed.
Those records do more than satisfy an auditor. They show which machines keep having the same problem, cut down on costly breakdowns, and help keep fires off the tipping floor and the working face.

The walkaround is the simplest safety tool we have. It needs no special equipment, only time and attention. Ten minutes at the start of the shift is a small price to make sure the machine, and everyone around it, gets through the day in one piece.

An Investment in Safety
The walkaround inspection is for safety and prolonging the life of the machine. It needs to be used properly and effectively to be useful. This is a task that cannot be ignored. The walkaround inspection can make your site safer and can reduce your maintenance cost as well. Both can be achieved in 10 to 15 minutes every day. That is a good return on that time investment.

Supervisors, operators, and the maintenance team all need to work together to ensure walkarounds are being done properly and that any defects that are written up are fixed. The status of the repair should be communicated to everyone frequently. I have seen many times at sites where it does not happen, and it causes friction between the field team and maintenance. | WA

Clay Layne is Founder of PurposeFirst and brings more than 30 years of experience in heavy equipment operations and safety. A 17-year veteran of Caterpillar Inc., Clay worked alongside engineers in research and development and led operator training focused on best practices and safety in the waste industry. His lifelong mission is to make the industry safer for all frontline workers through leadership, education, and a culture of accountability. He can be reached at (309) 397-3609 or e-mail [email protected].

If you have a topic or industry story that you would like to share or want to see written about, reach out to Clay via phone or e-mail.

Sponsor